|
Fastener Type |
Use To Fasten |
|
1" #8 rh wood screw |
closures to blocking lean-to "7" gables |
|
1" #10 rh wood screw |
ridge end closure 1365 (L & R) LT "7" |
|
1" #12 rh wood screw |
purlin angle fitting to blocking "7" gables |
|
1 1/2" #12 rh wood screw |
angle fitting at lean-to-roof and gable, bar,
ridge, ridge splice, closure to blocking, bar to
scribing all models |
|
3/8" #6 rh self-tapping screw type A |
door sweep to door bottom |
|
3/8" #6 rh self-tapping screw type Z |
door check fitting to sill, eave, ridge to bar
and buck casting to sill |
|
1/2" #8 rh self-tapping screw type Z |
barcaps to bar |
|
1/2" #10 rh self-tapping screw type Z |
angle fitting to sill, eave, ridge to bar and
buck casting to sill |
|
5/8" #10 rh self-tapping screw type Z |
angle fitting to header |
|
3/4" #10 rh self-tapping screw type Z |
sash junction closure to ridge at partition and
break in sash run |
|
3/4" #14 rh self-tapping screw type Z |
angle fitting partiation sill, flat brace to
sill (g to g models) |
|
7/8" #12 rh self-tapping screw type A |
angle fitting to masonry at door bucks |
|
1/2" #10 fh self-tapping screw type Z |
hinge to buck and door |
|
1/4 .20 X 3/8 rh mach. sc. w/nut |
splice at header, eave-angle fitting at eave
end |
|
1/4 .20 X 5/8 rh mach. sc. w/nut |
angle fitting at sill, buck spreader, deck bar,
g to g gable corner splice at bottom rail ridge,
shafting and header end |
|
1/4 .20 X 3/4 rh mach. sc. w/nut |
rafter splice, sill corner casting, sash,
muntin |
|
1/4 .20 X 1" rh mach. sc. w/nut |
bar splice, sash muntin at splice |
|
1/4 .20 X 2" rh mach. sc. w/nut |
buck to bar at side entrance |
|
24 X 1/2" #10 hex. hd. mach. bolt w/nut,
aluminum |
sash bearer fitting to bottom rail |
|
1/4" X 3/4" hex. hd. mach. bolt w/nut,
aluminum |
vent rod to sash bearer |
|
1/4 X 1" hex. hd. mach. bolt w/nut, lock washer.
galv. |
motor bracket z fitting to bar |
|
1/4 X 1 1/2" hex. hd. mach. bolt w/nut, lock
washer. galv. |
vent shafting coupling |
|
1/4" X 1 1/8" shoulder bolt w/nut and lock
washer. galv. |
vent sash arm and rod assembly |
|
1/4" X 5/8" T-bolt w/nut and lock washer.
galv. |
angle fitting at buck closure - lock strike buck
to sill fitting |
|
1/4" X 7/8" T-bolt w/nut and lock washer.
galv. |
buck and bar to gable rafter, angle purlin to
buck and bar. angle post to g to g. extension
bar |
|
1/4 .20 X 3/8 fh. mach. sc. w/nut aluminum |
splice at vent top rail |
|
1/4" X 1" carr. bolt w/nut and lock washer,
galv. |
motor bracket to z fitting |
|
#9039 rawl plug |
angle fitting at buck closer to masonry |
